How To Install a New Toilet Close Coupled Tank?

0
53
close coupled toilet

The utilisation of the restroom is a component of regular existence that each of us takes for granted. It’s everywhere, it’s always there for us, and it’s not always the most glamorous of things. But when something goes wrong with a toilet, it can be a real disaster. It can take hours to get a plumber out to fix the issue and cost hundreds of dollars($ USD 100). Although close coupled toilets are among the one that is less likely to have problems or needs a replacement soon, but there comes a time when you are looking for its replacement either due to a problem or as an upgrade.

Contrary to largely helpful belief, a close coupled toilet is relatively simple and easier to install. Therefore, if you have a basic knowledge of plumbing or using the tools, then you can get it installed as a DIY project over the weekend. In this article, we went over the procedure of installing a close coupled toilet in step by step fashion.

What is meant by the term “close coupled toilet”?

The close linked toilet is one of the most common types of toilet found in homes across the United Kingdom. Almost everyone has either used it or seen it in their lifetime. It is a single piece of the toilet where a toilet bowl and a cistern closely join, making a single unit. It looks like a cistern or water tank sits on the back of the pan. This type of toilet is available in many shapes and sizes, and you will need to choose depending on your needs. Regardless of the design or type you choose; the installation method will remain the same. You may either have a short projection or a standard toilet for the installation.

Prior to Your Beginning

It is essential that you double check everything that you require for the installation before beginning the process. If the items have arrived through courier service, then open the box as soon as it arrives. You must make sure that the close coupled toilet is not damaged, and all the accessories are included in the box. So, you don’t come to know about it on the day of installation.

List of Tools You Need

You will need the following tools to start working on the close coupled toilet installation.

  • Crescent Wrench
  • Screwdrivers set
  • Silicone Sealant
  • Caulking gun
  • Adjustable pliers
  • Drill Machine
  • Drill Bits
  • Bubble Level
  • Safety Glasses and Rubber Gloves

Step By Step Process for a Close Coupled Toilet Installation

Here are the steps that you will need to take to fit a close coupled toilet.

Step 1. Remove the Old Toilet

To remove an old toilet, you should first turn off the shutoff valves on the water supply and the sewer lines. After this, you should use a plunger to clear the toilet of water. You should also use a toilet auger to remove the old toilet. After the toilet has been removed, you should remove the old wax ring and replace it with the new one. The toilets are fixed on the floor with the nuts and bolts. A screwdriver will be required to remove It from the place with possibly a spanner. These are there for some time; therefore, they may be difficult to remove. In addition to that, there may need silicone sealant around the toilet bowl that you will need to remove by cutting through a sharp knife.

Step 2. Fitting a New Toilet

Although it may seem a bit complicated, it is the same step taken to remove the toilet in reverse order. You may have to assemble the interior parts if these are not fitted already. Make sure you don’t fit the things too tightly. Once you have made sure that everything is in place, you can place the toilet set in the right position as per drainage. You should check its level with the bubble level as well. It should line up or comply with the original fixing holes. If it fits the older position rightly, it will make fitting easier. In that case, you might be required to create more holes in the ground with a drill. Simply mark the position and use a drill machine to create the holes. Toilet bowls and cisterns come with predrilled holes. You don’t need to worry about it. Now remove the toilet and attach the drainage pipeline while keeping it in the same position. You can ask someone to help you with it for a few minutes. Once it is attached, you may want to seal it with a sealant.

Step 3. Tight the Screws and Reattach the Water Supply

Once in the right position fill, you can start putting screws in the holes. But make sure that holes are filled with the drill bits. You have to check to see that the screws are all the way screwed in. Now you can start working on reattaching the water supply. Establish a connection between the cistern or water tank and all of the pipes that bring in the water supply. These are usually an easy fix, and you will need to put it in the same position as it was before with the older toilet.

Step 4. Seal the Gaps

 It is important that you don’t leave any gaps on the floor unsealed. For example, you should fill the gaps. Simply fill the caulking gun with sealant and fill the gaps on the ground and toilet bowl.

Final Verdicts

In spite of the fact that doing things yourself can be a good way to save time and money, you should never attempt to plumb or install your own products without first hiring a skilled professional.

The aforementioned instructions are only meant to serve as a reference when it comes to installing your new toilet; they are not intended to cover the entirety of the plumbing and installation process.

LEAVE A REPLY

Please enter your comment!
Please enter your name here

56 − 51 =